GATR Carbide Bits

The DMC Wear Parts house brand

Carbide that bites. Boards that last.

GATR is our own line of carbide grader bits and scarifier boards, built for the crews who keep gravel roads smooth. The bits turn as they cut, so the carbide wears evenly and stays sharp. The boards hold them straight, with up to three levels of hard electrode protection.

GATR scarifier boards with carbide bits mounted on a motor grader
GATR boards and bits, mounted and ready to grade.
22 mmFits 22 mm bit boards
50 / boxFree shipping to the Lower 48
4 bit stylesSharp or blunt, with or without carbide overlay
3 ratingsOf board, plus Quick Change for Borox BluSteel

Why GATR

Why road crews run GATR

A high-quality aftermarket bit at a fraction of the cost of the big brand names, on a board built to take the abuse.

Carbide that rotates

Each bit turns as it cuts, so the tungsten carbide tip wears evenly and stays sharp longer than a steel edge.

Swap a bit, not a blade

Replace or move single bits along the moldboard with a bit removal tool, and keep a straight cutting edge.

Fits what you run

Made for 22 mm bit boards. Each part page shows how tight a spacing that bit fits.

Priced to wear out

Bits ship 50 to a box with free shipping to the Lower 48, so stocking up costs less.

Built for:Washboards and potholesHard-packed, high-impact roadsCompacted dirt and frozen groundIce and hard-packed snow

GATR bits

Carbide grader bits

Sharp tips to dig in, blunt tips for long wear, and carbide overlay heads for the roughest roads. Tap Drawing on any card to see its exact dimensions.

GATR G87KCSBSR carbide grader bit, 3D renderingGATR G87KCSBSR carbide grader bit, 3D rendering technical drawing
G87KCSBSR

22 mm sharp carbide grader bit

Carbide tip
25 mm sharp
Retainer
Barbed ring
Length
86 mm
Bits per foot
Up to 7

Replaces Kennametal C87KCSBSR

Board needs the milled ring in each holder

Drawing, specs & quote
Carbide overlay
GATR G87KCSBSR-CO carbide grader bit, 3D renderingGATR G87KCSBSR-CO carbide grader bit, 3D rendering technical drawing
G87KCSBSR-CO

22 mm sharp carbide grader bit

Carbide tip
25 mm sharp
Retainer
Barbed ring
Length
86 mm
Bits per foot
Up to 7

Board needs the milled ring in each holder

Drawing, specs & quote
GATR G855HDW carbide grader bit, 3D renderingGATR G855HDW carbide grader bit, 3D rendering technical drawing
G855HDW

22 mm blunt carbide grader bit

Carbide tip
16.9 mm blunt
Retainer
Washer + sleeve
Length
77.5 mm
Bits per foot
Up to 8

Replaces Kennametal C855HD

Drawing, specs & quote
Carbide overlay
GATR G855HDW-CO carbide grader bit, 3D renderingGATR G855HDW-CO carbide grader bit, 3D rendering technical drawing
G855HDW-CO

22 mm blunt carbide grader bit

Carbide tip
16.9 mm blunt
Retainer
Washer + sleeve
Length
77.5 mm
Bits per foot
Up to 8
Drawing, specs & quote

Barbed ring bits: your board needs the milled ring inside each holder for the barb to sit in. Some older boards don't have it, so check yours before ordering.

Sold by the box: 50 bitsShipping: free to the Lower 48Stock: confirmed with your quote

Up close

See a GATR bit before you buy

This is the G855HDW-CO: a 22 mm blunt bit with a carbide overlay head, washer and sleeve. Every GATR bit page has its own drawing, 3D view and video.

GATR boards

Scarifier boards

One-piece boards for 22 mm bits, 6 bits per foot, in 3, 4 and 5 ft lengths. Pick the protection for your roads, then the lengths for your moldboard.

GATR HDXL scarifier board, 3D renderingGATR HDXL scarifier board, 3D rendering technical drawing

HDXL

Compare to Severe Duty

Protection

Adds a hard electrode strip along the holders, so the face doesn't wash out and no cover plate is needed.

Best for
Abrasive gravel that wears boards out
Size
7.3" x 1-1/4"
Lengths
3 ft, 4 ft
Mounting
3/4" Plow Bolts
GATR HDX-TREME scarifier board, 3D renderingGATR HDX-TREME scarifier board, 3D rendering technical drawing

HDX-TREME

Compare to Extreme Duty

Protection

Hard electrode strip plus a diamond crosshatch over the face and around every bolt hole.

Best for
The most abrasive roads
Size
7.3" x 1-1/4"
Lengths
3 ft, 4 ft
Mounting
3/4" Plow Bolts
GATR Quick Change scarifier board, 3D renderingGATR Quick Change scarifier board, 3D rendering technical drawing

Quick Change

Borox BluSteel system

Quick change system

Made for the Borox BluSteel quick change system, with a hard electrode strip on the face. Not a bolt-on board.

Best for
Crews already running BluSteel
Size
6.1" x 12 mm plate
Lengths
3 ft, 4 ft
Mounting
Borox BluSteel quick change
Compare all 9 GATR boards
Part #RatingLengthBitsHeight x thicknessHard electrodeWeight
GATR-36HDHD3 ft186" x 1-1/4"None71 lb
GATR-48HDHD4 ft246" x 1-1/4"None95 lb
GATR-60HDHD5 ft306" x 1-1/4"None119 lb
GATR-36XLHDXL3 ft187.3" x 1-1/4"Strip85 lb
GATR-48XLHDXL4 ft247.3" x 1-1/4"Strip119 lb
GATR-36XTHDX-TREME3 ft187.3" x 1-1/4"Strip + crosshatch85 lb
GATR-48XTHDX-TREME4 ft247.3" x 1-1/4"Strip + crosshatch116 lb
GATR-QC36Quick Change3 ft186.1" x 12 mm plateStrip46 lb
GATR-QC48Quick Change4 ft246.1" x 12 mm plateStrip62 lb

How many boards and bits?

MoldboardBoardsBits
12 ft3 x 4 ft72 bits
13 ft3 x 3 ft + 1 x 4 ft78 bits
14 ft2 x 3 ft + 2 x 4 ft84 bits
16 ft4 x 4 ft96 bits

Two boxes of GATR bits (100) fill any of these moldboards with spares to rotate in.

How to order

  1. Pick your bits and boardsOpen any part for its drawing, 3D view and specs.
  2. Add them to your quote listBoard pages add bits and 3/4" Plow Bolts, nuts and washers in one step.
  3. Get your quoteWe confirm stock, freight and lead time with your quote.

“All of the aftermarket scarifier parts I ordered from DMC Wear Parts bolted onto my equipment perfectly and are thicker than the factory pieces. Ordering from the company was easy and personable with very fast shipping.”

Neil, private contractor, Illinois

Need a board built your way?

GATR boards can be made to your length, height, bit count or paint color. Tell us what you run.

Running Kennametal? We're an authorized Kennametal dealer too: Kennametal bits and scarifier blades.

Quick & Free Quotes

(605) 840-8082

American Owned

OEM part numbers and names are referenced to aid in identifying replacement parts. We do not imply that our products are sponsored, affiliated, or approved by the original equipment manufacturers.

Quote list (0)Call
DMC Wear Parts